View SLA6805MP_7322617.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SLA6805MP description the SLA6805MP inverter power module (ipm) device provides a robust, highly-integrated solution for optimally controlling 3-phase motor power inverter systems and variable speed control systems used in energy-conserving designs to drive motors of residential and commercial appliances. these ics take 230 vac input voltage, and 3 a (continuous) output current. they can withstand voltages of up to 600 v (igbt breakdown voltage). the sla6800mp power package includes an ic with all of the necessary power elements (six igbts), pre-driver ics (two), and flyback diodes (six), needed to configure the main circuit of an inverter. this enables the main circuit of the inverter to be configured with fewer external components than traditional designs. applications include residential white goods (home applications) and commercial appliance motor control: ? air conditioner fan ? refrigerator compressor ? dishwasher pump features and benefits ? built-in pre-drive ic ? igbt power element ? cmos compatible input (3.3 to 5 v) ? high-side gate driver using bootstrap circuit or floating power supply ? built-in protection circuit for controlling power supply voltage drop ? overcurrent protection circuit (ocp) ? output of fault signal during operation of protection circuit ? output current 3 a ? small sip (sla 23-pin) high voltage 3-phase motor driver functional block diagram not to scale low-side driver delay delay delay vcc lin1 uv detect ocp blank timer and hold lin2 lin3 rs lo 1 lo 2 lo 3 com rc fo (totem pole ) vtrip pulse filter uv detect r r s q pulse pulse generator vb ho hs com vcc hin hv level shift high-side driver figure 1. driver block diagrams. leadform 2152 (iec) leadform 2151 leadform 2153 packages: power sip 28610.02, rev. 3
high voltage 3-phase motor driver SLA6805MP 2 all performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature, t a , of 25c, unless oth er wise stated. recommended operating conditions characteristic symbol remarks min. typ. max. units main supply voltage v bb between vbb and ls, i bb 2 a ? 300 450 v logic supply voltage v cc between vcc and com 13.5 ? 16.5 v dead time t dead 1.5 ? ? s junction temperature t j ? ? 125 c selection guide part number packing igbt breakdown voltage, v ces (min) (v) igbt saturation voltage, v ce(sat) (typ) (v) output current continuous, i o (max) (a) pulsed, i op (max) (a) SLA6805MP 18 pieces per tube 600 1.75 3 6 absolute maximum ratings , valid at t a = 25c characteristic symbol remarks rating unit igbt breakdown voltage v ces v cc = 15 v, i c = 1 ma, v in = 0 v 600 v logic supply voltage v cc between vcc and com 20 v bootstrap voltage v bs between vb and hs (u,v, and w phases) 20 v output current, continuous i o t c = 25c 3 a output current, pulsed i op pw 1 ms, duty cycle = 50% 6 a input voltage v in ?0.5 to 7 v rc pin input voltage v rc between rc and com; c c 2200 pf 20 v allowable power dissipation p d t c = 25c, all elements operating 32 w thermal resistance (junction to case) r jc all elements operating (igbt) 3.8 c/w all elements operating (fwd) 5.4 c case operating temperature t cop ?20 to 100 c junction temperature (mosfet) t j 150 c storage temperature t stg ?40 to 150 c allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 3 vcc2 lin1 vcc1 hin1 com1 vb1 ho3 hs3 lin2 lin3 fo com2 lo1 lo2 lo3 m controller 15v hvic lvic hin2 hin3 vb2 vb3 ho2 ho1 hs1 hs2 10 234 5 9 6 7 8 1 13 12 14 11 17 16 15 23 22 19 18 20 21 rcin rs rs rc cc SLA6805MP note: ? all of the input pins are connected to gnd with internal pull-down resistors rated at 100 k , however, an external pull-down resistor may be required to secure stable condition of the inputs if high impedance conditions are applied to them. ? to use the ocp circuit, an external shunt resistor, rs, is needed. the rs value can be obtained from the formula: r s ( ) = 0.5 v / overcurrent detection set current (a) . ? a blanking timer is built-in to mask the noise generated on rs at turn-on. ? the external electrolytic capacitors should be placed as close to the ic as possible, in order to avoid malfunctions from external noise interference. put a ceramic capacitor in parallel with the electrolytic capacitor if further reduction of noise susceptibility is necessary. typical application diagram allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 4 electrical characteristics, valid at t a =25c, c c 2200 pf, unless otherwise noted characteristics symbol conditions min typ max units logic supply voltage v cc between vcc and com 13.5 15 16.5 v logic supply current i cc v cc = 15 v ? 4 6 ma input voltage v ih v cc = 15 v, output on ? 2.0 2.5 v v il v cc = 15 v, output off 1.0 1.5 ? v input voltage hysteresis v ihys v cc = 15 v ? 0.5 ? v input current i ih high side, v cc = 15 v, v in = 5 v ? 50 100 a i il low side, v cc = 15 v, v in = 0 v ? ? 2 a undervoltage lock out v uvhl high side, between vb and u, v, or w 9.0 10.0 11.0 v v uvhh 9.5 10.5 11.5 v v uvhhys high side, hysteresis ? 0.5 ? v v uvll low side, between vb and u, v, or w 10.0 11.0 12.0 v v uvlh 10.5 11.5 12.5 v v uvlhys low side, hysteresis ? 0.5 ? v fo terminal output voltage v fol v cc = 15 v 0 ? 1.0 v v foh 4.0 ? 5.5 v overcurrent protection trip voltage v trip v cc = 15 v 0.45 0.50 0.55 v overcurrent protection hold time t p1 v rc = 15 v, r c = 1 m , c c = 1000 pf ? 260 ? s t p2 v rc = 5 v, r c = 330 k , c c = 2200 pf ? 870 ? s blanking time t blank v cc = 15 v ? 2 ? s igbt breakdown voltage v ces v cc = 15 v, i c = 1 ma, v in = 0 v 600 ? ? v igbt leakage current i ces v cc = 15 v, v ce = 600 v, v in = 0 v ? ? 1 ma igbt saturation voltage v ce(sat) v cc = 15 v, i c = 3 a, v in = 5 v ? 1.75 2.1 v diode forward voltage v f v cc = 15 v, i f = 3 a, v in = 0 v ? 1.65 2.0 v diode recovery time t rr i f = 3 a, di / dt = 100 a/ s ? 50 ? ns switching time, high side t dh(on) v bb = 300 v, v cc = 15 v, i c = 3 a, 0 v v in 5 v, inductive load ? 315 ? ns t rh ?55?ns t dh(off) ? 455 ? ns t fh ? 175 ? ns switching time, low side t dl(on) ? 430 ? ns t rl ? 100 ? ns t dl(off) ? 410 ? ns t fl ? 190 ? ns allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 5 low side driver input/output timing diagrams lin vcc lo v uvhh rs fo v trip(h) t blank t blank after uvlo is released, ic operation is started by the first rising edge of input after rc charging and releasing, the ocp operation is started by the first rising edge of input t p v uvhl v trip(l) uvlo release rc slope by rc,cc high side driver input/output timing diagrams hin vb-hs ho v uvhh v uvhl after uvlo is released, ic operation is started by the first rising edge of input uvlo release t p = r c c c {?ln (1?3.5 / v rc )} where c c 2200 pf allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 6 leadform 2151 leadform 2152 leadform 2153 1357911131517192123 246810121416182022 1 41014 313 68 5 7 9 11 15 17 19 21 23 212 16 18 20 22 2 46 8 10 12 14 16 18 20 22 1 3 5 7 9 11 13 15 17 19 21 23 pad side pad side pad side terminal list table number name function 1 u output of u phase 2 vb1 high side bootstrap terminal (u phase) 3 vb2 high side bootstrap terminal (v phase) 4 vb3 high side bootstrap terminal (w phase) 5 vcc1 high side logic supply voltage 6 com1 high side logic gnd terminal 7 hin3 high side input terminal (w phase) 8 hin2 high side input terminal (v phase) 9 hin1 high side input terminal (u phase) 10 vbb1 main supply voltage 1 (connect to vbb2 externally) 11 vbb2 main supply voltage 2 (connect to vbb1 externally) 12 w1 output of w phase (connect to w2 externally) 13 v output of v phase 14 w2 output of w phase (connect to w1 externally) 15 ls2 low side emitter terminal (connect to ls1 externally) 16 rcin overcurrent protection hold time adjustment terminal 17 ls1 low side emitter terminal (connect to ls1 externally) 18 lin3 low side input terminal (w phase) 19 lin2 low side input terminal (v phase) 20 lin1 low side input terminal (u phase) 21 com2 low side gnd terminal 22 fo overcurrent protection fault-signal output terminal 23 vcc2 low side logic supply voltage pin-out diagrams allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 7 terminal core material: cu terminal plating: ni, with pb-free solder coating recommended attachment: solder dip (sn-ag-cu) dimensions in millimeters branding area branding codes (exact appearance at manufacturer discretion): 1st line, type: SLA6805MP 2nd line, lot: ymdd where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the date exposed heatsink pad 2x exposed tie bar 1.27 0.5 0.6 0.65 +0.2 ? 0.1 9.3 +0.1 ? 0.5 0.55 +0.2 ? 0.1 16.4 0.2 24.4 0.2 ?3.2 0.15 31 0.2 gate protrusion 2x gate protrusion 9.9 0.2 12.9 0.2 16 0.2 a a b measured at pin tips to case top 1 3 5 7 9 11 13 15 17 19 21 23 246810121416182022 1.7 0.1 4.8 0.2 r1 ref 4.3 ref 4.5 0.7 5 0.5 2.45 0.2 bsc b ?3.2 0.15 31.3 0.2 view a deflection at pin bend 0.7 max 0.7 max view a package outline drawing leadform 2151 dual rows, 23 alternating pins; vertical case mounting; pin #1 opposite pad side leadframe plating pb-free. device composition complies with the rohs directive. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 8 leadform: 2152 terminal core material: cu terminal plating: ni recommended attachment: solder dip (sn-ag-cu) dimensions in millimeters branding codes (exact appearance at manufacturer discretion): 1st line, type: SLA6805MP 2nd line, lot: ymddt where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the date t is the tracking letter branding area 2x exposed tie bar 1.27 0.5 0.6 0.6 +0.15 ? 0.05 8.7 +1 ? 0.5 0.5 +0.2 ? 0.1 16.4 0.2 24.4 0.2 ?3.2 0.15 31 0.2 gate protrusion 2x gate protrusion 9.9 0.2 12.9 0.2 16 0.2 a a b measured at pin tips to case top 1 41014 3 57911 13 15 17 19 21 23 2 68 12 16 18 20 22 1.7 0.1 4.8 0.2 r1 ref 3.7 ref 3.1 0.7 3.1 0.7 5 0.5 2.45 0.2 bsc b ?3.2 0.15 31.3 0.2 view a exposed heatsink pad deflection at pin bend 0.7 max 0.7 max view a package outline drawing leadform 2152 triple rows (iec compliant), 23 alternating pins; vertical case mounting; pin #1 on pad side leadframe plating pb-free. device composition complies with the rohs directive. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 9 leadform: 2153 terminal core material: cu terminal plating: ni recommended attachment: solder dip (sn-ag-cu) dimensions in millimeters branding codes (exact appearance at manufacturer discretion): 1st line, type: SLA6805MP 2nd line, lot: ymddt where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the date t is the tracking letter branding area exposed heatsink pad 1.27 0.1 0.6 16.4 0.2 24.4 0.2 ?3.2 0.15 31 0.2 gate protrusion 9.9 0.2 12.9 0.2 16 0.2 a a b to case top 1.7 0.1 4.8 0.2 r1 ref 0.6 0.1 0.5 0.1 2.45 0.2 bsc b ?3.2 0.15 31.3 0.2 view a 2 46 8 10 12 14 16 18 20 22 1 3 5 7 9 11 13 15 17 19 21 23 measured at pin exit from case 4.4 ref 2.2 0.7 bsc 2.2 0.7 bsc 3 0.5 bsc deflection at pin bend 0.7 max 0.7 max view a 2x gate protrusion 2x exposed tie bar package outline drawing leadform 2153 dual rows, 23 alternating pins; pins bent 90 for horizontal case mounting; pin #1 in outer row leadframe plating pb-free. device composition complies with the rohs directive. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 10 580 13.8 31.2 x 137 186 621 z y maximum 12 tubes in y direction maximum 3 tubes in z direction maximum pieces per carton: 18 pieces per tube 12 tubes per layer x 3 layers of tubes 648 pieces per carton tube material: pvc maximum 18 pieces per tube (pins aligned along x direction) rubber plug each end packing specification leadforms 2151 and 2152 dimensions in millimeters allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 11 packing specification leadform 2153 dimensions in millimeters 580 158 310 x 130 185 610 z y maximum 12 tubes in y direction maximum 12 tubes in z direction maximum pieces per carton: 18 pieces per tube 10 tubes per layer x 3 layers of tubes 540 pieces per carton tube material: pvc maximum 18 pieces per tube (pins aligned along x direction) rubber plug each end allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 12 warning ? these devices are designed to be operated at lethal voltages and energy levels. circuit designs that embody these components must conform with applicable safety requirements. pre cau tions must be taken to prevent accidental contact with power-line potentials. do not connect ground ed test equipment. the use of an isolation transformer is recommended during circuit development and breadboarding. because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. cautions for storage ? ensure that storage conditions comply with the standard temperature (5c to 35c) and the standard relative humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity. ? avoid locations where dust or harmful gases are present and avoid direct sunlight. ? reinspect for rust on leads and solderability of products that have been stored for a long time. cautions for testing and handling when tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between adjacent products, and shorts to the heatsink. remarks about using silicone grease with a heatsink ? when silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. if more silicone grease than required is applied, it may produce stress. ? volatile-type silicone greases may permeate the product and produce cracks after long periods of time, resulting in reduced heat radiation effect, and possibly shortening the lifetime of the product. ? our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: type suppliers g746 shin-etsu chemical co., ltd. yg6260 momentive performance materials, inc. sc102 dow corning toray silicone co., ltd. heatsink mounting method torque when tightening mounting screws. the recommended tightening torque for this product package type is: 58.8 to 78.4 n?cm (6.0 to 8.0 kgf?cm). soldering ? when soldering the products, please be sure to minimize the working time, within the following limits: 2605c 10 s 3805c 5 s ? soldering iron should be at a distance of at least 1.5 mm from the body of the products electrostatic discharge ? when handling the products, operator must be grounded. grounded wrist straps worn should have at least 1 m of resistance to ground to prevent shock hazard. ? workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. ? when using measuring equipment such as a curve tracer, the equipment should be grounded. ? when soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent leak voltages generated by them from being applied to the products. ? the products should always be stored and transported in our shipping containers or conductive containers, or be wrapped in aluminum foil. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
high voltage 3-phase motor driver SLA6805MP 13 the products described herein are manufactured in ja pan by sanken electric co., ltd. for sale by allegro microsystems, inc. sanken and allegro reserve the right to make, from time to time, such de par tures from the detail spec i fi ca tions as may be re quired to per mit im- prove ments in the per for mance, reliability, or manufacturability of its prod ucts. therefore, the user is cau tioned to ve rify that the in for ma tion in this publication is current before placing any order. when using the products described herein, the ap pli ca bil i ty and suit abil i ty of such products for the intended purpose s hall be reviewed at the users responsibility. although sanken undertakes to enhance the quality and reliability of its prod ucts, the occurrence of failure and defect of sem i con duc tor products at a certain rate is in ev i ta ble. users of sanken products are requested to take, at their own risk, preventative measures including safety design of the equipme nt or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equip ment or apparatus (home ap pli anc es, office equipment, tele com mu ni ca tion equipment, measuring equipment, etc.). their use in any applicat ion requiring radiation hardness assurance (e.g., aero space equipment) is not supported. when considering the use of sanken products in ap pli ca tions where higher reliability is re quired (transportation equipment and its control systems or equip ment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written confirmation of your spec i fi ca tions. the use of sanken products without the written consent of sanken in applications where ex treme ly high reliability is required (aerospace equip- ment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. the information in clud ed herein is believed to be accurate and reliable. ap pli ca tion and operation examples described in this pub li ca tion are given for reference only and sanken and allegro assume no re spon si bil i ty for any in fringe ment of in dus tri al property rights, intellectual property rights, or any other rights of sanken or allegro or any third party that may result from its use. the contents in this document must not be transcribed or copied without sanken?s written consent. copyright ? 2008-2010 allegro microsystems, inc. this datasheet is based on sanken datasheet ssj-03405. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com

▲Up To Search▲

Price & Availability of SLA6805MP

	To Download SLA6805MP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .